|
|
My Account
|
How to wrap a gift
Wrap a gift using Starpak Industries Ribbons and create a sensation! These bow
making techniques are easy to follow and add bow-brilliance to wrapped packages,
gift baskets, floral arrangements and more.
Florist Bow
Materials:
Directions:
- 8" from one end of ribbon, pinch firmly between thumb and index
finger.
- Make a 5" loop (half the size of finished bow) pinch tightly.
If ribbon is one-sided, twist length to right side. Make a second loop
and pinch over first two pinches.
- Repeat this process forming 4 loops on each side.
- Make a center knot by forming a small loop over your thumb, pinch and wire
all loops together, trim excess. Wire 14" length to back for
tails.

Pompom Bow
Materials:
- 5 yds. craft type ribbon, small piece of wire
Directions:
- With ribbon, form a 9" loop equal in size to the diameter of the
finished bow.
- Wrap remaining ribbon around loop as many times as is desired for bow.
- Flatten loops and cut off triangles at end, being careful not to cut too
close to the center.
- Bring ends together to meet in center, overlapping triangles.
- Secure ribbon at center over notches with wire. Pull out loops,
twist towards center, alternating sides to form pompom.

Starburst Bow
Materials:
- 2 yds of ribbon of your choice
Directions:
|

|
- Beginning at one end of 1 yard of ribbon, form a 4" loop and pinch
together between thumb and index finger. Bring ribbon down and under
to form a 4" loop at bottom and pinch together to secure. Repeat
this process forming a 4 loop bow. Wire tightly.
- Using 2-16" lengths of ribbon, pinch each at center and secure with
wire to either side of 4 loop bow forming tails.
- To complete the bow, fold a 4" length of ribbon in half and wrap
around center of 4 loop bow and tails. Glue at back to secure.
Single Ribbon Loop Bow
Materials:
- 12" of ribbon of your choice.
Directions:
- Using a 12" length of ribbon, form a 4" loop at one end and
pinch together.
- Bring remaining ribbon up to extend beyond loop forming a tail.
Pinch together at base with floral pick and wire to secure.
Variation:
Using a longer length of ribbon, double or triple the number of loops for a
fuller look.


|
Wrapping the Package
Materials:
First, to determine the length of ribbon needed, use this formula: multiply
the length of the box x 2, multiply the width of the box x 2, multiply the depth
x 4, and add these numbers together. Then add about 3/4 yd. to 1 yd. extra
to make a bow.
Directions:
- Wrap ribbon around box, allowing for extra ribbon to tie bow. To do
this, one end of the ribbon needs to be twice as long as the other end.
(Fig.1)
- Twist ribbon around each other, bringing longer length of ribbon around
box, under bottom and back to top. (Fig. 2)
- Bring longer length over the twist, and slip it under, coming around and
out in the opposite corner. (Fig. 3&4)
- Pull both ends taut. Tie shoelace bow. (Fig. 5)
|
|
METRIC RIBBON
WIDTH CONVERSION
3/16" =
5mm
3/4" = 19mm
1/4" =
7mm
7/8" = 23mm
3/8" = 9mm 1 7/16" =
37mm
1/2" = 12mm 1 1/2" =
39mm
5/8" = 15mm 2 3/4" =
70mm
METRIC CONVERSION
Guide
Yards x .9 = Meters
Inches x 2.5 = Centimeters |
Browse the ribbons and bows available in our
shopping system:
www.starpak.ca/ribbons_bows.php
Starpak Industries
Plastic and Paper Packaging Products
|
|
|
|
|
|
|
Canada, 1443 256th Street, Aldergrove, British Columbia BC V4W 2G4, Canada, Phone : 604-607-0931, Fax : 604-607-0938, Toll-Free: 1-888-873-5511
Vancouver (BC), Coquitlam, Delta, Burnaby, Richmond, Abbotsford, Maple Ridge, Langley, Port Coquitlam, North Vancouver (BC), West Vancouver (BC), East Vancouver (BC), South Vancouver (BC), New Westminster
CANADA
Toronto Ontario, Calgary Alberta, Montreal Quebec, Winnipeg Manitoba,
Victoria BC, Edmonton Alberta, Ottawa Ontario, Regina Saskatchewan,
Saskatoon Saskatchewan, Quebec City Quebec Canada
Halifax Nova Scotia,New Brunswick PEI, St. Johns New Foundland,
Kingston Ontario, Yellowknife NWT, Yukon, Nunavut, Kamploops BC, Windsor Ontario Canada
|